I'm pulling an angled exhaust housing from a car that is getting parted. Got the vband clamp off and 3 of the 4 nuts to the engine, but I can't seem to reach that lower nut towards the driver's side? What's the trick or favorite tool here? I was trying a flexible ratcheting box wrench.
Worked on it for about 1/2 hour and decided to just give it a rest and attack it another day. I just don't seem to have any room back there to get a wrench on it and room to move. It's on a 99 AWD so technically wrong forum, but shouldn't be much different than any other. Mods can move if needed.
Pita Removing Turbo Exhaust Housing
Started by Dan A, May 21 2012 03:06 PM
8 replies to this topic
#1
Dan A
-
- Lifetime Supporter
-
- 1994 posts
Old Man Crew Pledge Pres.
Posted 21 May 2012 - 03:06 PM
99 V70R98 V70 GLT
#2
Keep Calm Chive On
-
- Lifetime Supporter
-
- 2909 posts
I Love To Pound Ash
Posted 21 May 2012 - 03:48 PM
I cut a 13mm wrench in half... its a bitch plain & simple.
Beiber: kurt i got with a cougar last weekend
Dr.PorkenheimersBonerJuice: no you didnt kev, you jacked it to pictures of teen mom. that isnt cougar
SHIT IM SELLIN ; SHIT YOU BUYIN. DONT BE A BITCH ; CLICK IT
Dr.PorkenheimersBonerJuice: no you didnt kev, you jacked it to pictures of teen mom. that isnt cougar
SHIT IM SELLIN ; SHIT YOU BUYIN. DONT BE A BITCH ; CLICK IT
#3
bergmjs
-
- Supporting Member
-
- 2060 posts
Level 3 Member
Posted 21 May 2012 - 04:30 PM
I wiggled a standard open-ended wrench in there and got it off and on. Took lots of patience and a few swears, but it's possible.
'95 854 T5M 195k - Koni Yellows, IPD Strut Brace, IPD CAI, IPD 25mm front sway, IPD Poly Upper, M56H, NA TB+Mani, Japanifold, OBX exhaust w/ angled housing, IPD springs, 2.25" Plumbed FMIC, 18T, ARD Blue - DEAD - To be parted out
'04 S60R - 125k
#4
Dan A
-
- Lifetime Supporter
-
- 1994 posts
Old Man Crew Pledge Pres.
Posted 21 May 2012 - 04:48 PM
I think I have a stubby 13mm wrench. Maybe I'll give that a try. I think walking away from it for the day was probably for the best and I just need to go at it fresh another day. Thanks.
99 V70R98 V70 GLT
#5
Rsterns
-
- Members
-
- 1216 posts
Level 3 Member
Posted 21 May 2012 - 08:37 PM
Try a ratcheting box wrench
'98 V70 T5 (Auto) At 280,000 fresh rebuild with port and polish ;Cryo treated everything, ARD Blue tune w/ IPD Intercooler and TME cat back exhaust,Koni FSD/ Eibach springs, IPD sways F/R, IPD HDEndlinks, IPD BBK Currently 407K miles... '99 V70 T5M (Was JRLs)
#6
bergmjs
-
- Supporting Member
-
- 2060 posts
Level 3 Member
Posted 22 May 2012 - 02:11 PM
Try a ratcheting box wrench
I'm pulling an angled exhaust housing from a car that is getting parted. Got the vband clamp off and 3 of the 4 nuts to the engine, but I can't seem to reach that lower nut towards the driver's side? What's the trick or favorite tool here? I was trying a flexible ratcheting box wrench.
'95 854 T5M 195k - Koni Yellows, IPD Strut Brace, IPD CAI, IPD 25mm front sway, IPD Poly Upper, M56H, NA TB+Mani, Japanifold, OBX exhaust w/ angled housing, IPD springs, 2.25" Plumbed FMIC, 18T, ARD Blue - DEAD - To be parted out
'04 S60R - 125k
#7
Dan A
-
- Lifetime Supporter
-
- 1994 posts
Old Man Crew Pledge Pres.
Posted 24 May 2012 - 03:28 AM
LOL. I wasn't going to point it out. 
Well, if the rain let's up, I'll go after it again this weekend.
Well, if the rain let's up, I'll go after it again this weekend.
99 V70R98 V70 GLT
#8
db130
-
- Lifetime Supporter
-
- 771 posts
Level 2 Member
Posted 24 May 2012 - 06:03 PM
i went through this myself recently. that nut is facing the front of the car and the issue for me was leverage. by the time i contorted my arm to reach the ratchet and/or wrench i just could not turn it loose
i ended up using a gearwrench x-beam wrench which is the longest wrench i had by far
i ended up using a gearwrench x-beam wrench which is the longest wrench i had by far
2000 V70XC SE, 162k '00 R Duals/Angled 15G/15 psi ST T5 tune/Delco TCV/UK 302s/180°F Stant Superstat/Samco hoses/IPD HD CBV/Sconeman intake
1998 S70 T5, 233k '00R 302s DIY AEM BCS/IPD Stage 1 ECU/IPD 3" Turboback
Check out the Delco BCS/TCV
#9
ande0549
-
- Members
-
- 77 posts
Level 1 Member
Posted 27 May 2012 - 04:05 PM
Use a crow foot wrench or better yet, a flare-nut crow foot!
98 S70 T5M, 157k
Upsolute ECU (ARD Blue next), Samco intercooler/Radiator hoses, R-manifold, Angle-flange 16T, EST 3" downpipe & 2.5" catback, Koni FSD, Eibach Pro-kit, IPD sway bars, QBM shift kit, R-bumper, 98 XC grille, Air pump delete
