gdog Posted May 18, 2017 Report Share Posted May 18, 2017 (edited) On 8/9/2016 at 7:50 AM, venderbroeck said: Anybody that has one of these care to share their experience? I got one recently but can't seem to get it to work. When I plug it in, it beeps out a little diddy but then I go for a drive and there's no file is on the sd card afterward. Do you have yours hard-wired into the car? So far I've only plugged into the obd2 port with it. Any trick I need to know about? Yes, logging is enabled permanently in the ecu; logging from laptop works fine. Edited May 18, 2017 by gdog Quote Link to comment Share on other sites More sharing options...
Avinitlarge Posted May 18, 2017 Report Share Posted May 18, 2017 I have one and it works perfectly. How did you format the SD card? Quote Link to comment Share on other sites More sharing options...
venderbroeck Posted November 27, 2017 Author Report Share Posted November 27, 2017 (edited) Coming soon: Edited November 27, 2017 by venderbroeck 1 Quote Link to comment Share on other sites More sharing options...
gdog Posted November 27, 2017 Report Share Posted November 27, 2017 15 hours ago, venderbroeck said: Coming soon: Umm, what is coming soon? Is that your new engine block? Quote Link to comment Share on other sites More sharing options...
venderbroeck Posted November 28, 2017 Author Report Share Posted November 28, 2017 It is, I've finally got more or less all the parts to build it. :D I'll probably keep a little build log in here, although most ppl here already saw an engine being built ofc :P Quote Link to comment Share on other sites More sharing options...
Brad850 Posted November 29, 2017 Report Share Posted November 29, 2017 19 hours ago, venderbroeck said: It is, I've finally got more or less all the parts to build it. :D I'll probably keep a little build log in here, although most ppl here already saw an engine being built ofc :P VS needs all it can get. You should definitely make a separate build thread. 1 Quote Link to comment Share on other sites More sharing options...
Beunhaas Posted December 28, 2017 Report Share Posted December 28, 2017 any christmas presents here? :D Quote Link to comment Share on other sites More sharing options...
oblark Posted December 30, 2017 Report Share Posted December 30, 2017 I think I've got a problem with my data logger. It's been as good as gold up until today when it would only log for 5 - 7 seconds then it stops. I can connect to it no problem but when I disconnect I get this error message. Any ideas ? Quote Link to comment Share on other sites More sharing options...
oblark Posted March 9, 2018 Report Share Posted March 9, 2018 Maarten, Can you please reply to my messages. Thanks Quote Link to comment Share on other sites More sharing options...
venderbroeck Posted September 1, 2018 Author Report Share Posted September 1, 2018 Soo it's been quite a while. As I've already sent to a lot of people, I had to get away from the forums and other volvo related stuff to finish graduating. I'm back again though, so time to catch up again. My engine build has progressed a tiny bit, but not much. I've been looking around for some valve buckets. The valve lash had become too small, as I had ground the seats for the three angle valve job. Those buckets are ~18 euro a piece, and I needed 13 new ones :P After looking around some I had found a webpage online where someone described machining the buckets to size. My uncle is a machinist, and fortunately he agreed to machine the buckets for me. So lucky break there, saving me a lot of money. When I get those back the engine is ready to be put together the rest of the way. I have all the parts needed on hand. Apart from that I've been busy cooking up a BBK to got with my increased power. I will explain it in a little more detail when my engine build thread gets de-archived (mods? :) ). I'm now in the process of getting back to everybody who has sent me a message the past few months. Feel free to ping me though. 2 Quote Link to comment Share on other sites More sharing options...
razorx Posted September 1, 2018 Report Share Posted September 1, 2018 Congratulations Maarten! Quote Link to comment Share on other sites More sharing options...
dim28 Posted November 12, 2020 Report Share Posted November 12, 2020 Hi,i´d like to buy one RPM defloater.How can i contact you? Let me know at siziff78@gmail.com I ll appreciate your help.Thanks Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.